Bj3 file extension

For Google Chrome, this is the. This file stores incompletely downloaded content. The browser allows resuming the download using. Every time Chrome starts downloading a file, the browser creates a file with the extension. For example, if you download Dropbox.

Table Display option code overview Display Option Vertical Resolution p p i p p p p p i. All options and alignments are stored when pressing cursor right and then the OK-button SW Maintenance.

SW Events. Not useful for Service purposes. In case of specific software problems, the development department can ask for this info. HW Events. Operation hours PDP. Here you are able to reset the operations hours of the plasma display. This has to be done in case of replacement of the display. Upload to USB. The four items are Channel list, Personal settings, Option codes and Display-related alignments. To upload the settings you have to select each item separately, press cursor right, confirm with OK and wait until Done appears.

Uploading is of course only possible if the software is running and if you have picture. This method is created to be able to save the customers TV settings and to store them into another SSB. Download from USB. Same way of working as with uploading. To make sure that the download of the channel list from USB to the TV is executed properly, it is necessary to restart the TV and tune to a valid preset if necessary. The selected item will be highlighted. De activate the selected sub menu.

With the OK key, it is possible to activate the selected action. The service technician can then ask the customer to activate the CSM, in order to identify the status of the set. Now, the service technician can judge the severity of the complaint.

In many cases, he can advise the customer how to solve the problem, or he can decide if it is necessary to visit the customer. The CSM is a read only mode; therefore, modifications in this mode are not possible. When in this chassis, CSM is activated, a colour bar test pattern will be visible for 5 seconds.

This test pattern is generated by the Pacific3. So if you see this test pattern you can determine that the back end video chain Pacific3, LVDS and display is working. The file Csm. This info can be handy if you dont have picture. Note: Activation of the CSM is only possible if there is no user menu on the screen!

In this way, it is not necessary for the customer to look at the rear of the TV-set. ComPair will foresee a possibility to do this. Displays the production code the serial number of the TV.

Code 1. Gives the latest five errors of the error buffer. As soon as the built-in diagnose software has detected an error the buffer is adapted. The last occurred error is displayed on the leftmost position. Each error code is displayed as a 2-digit number. When less than 10 errors occur, the rest of the buffer is empty See also paragraph Error Codes for a description. Code 2. Gives the first five errors of the error buffer.

Options 1. Options 2. Digital Natural Motion. Gives the last status of the Digital Natural Motion setting, as set by the customer.

Possible values are Off, Minimum and Maximum. See DFU on how to change this item. Pixel Plus. Gives the last status of the Pixel Plus setting, as set by the customer. Possible values are On and Off. Gives the last status of the DNR setting, as set by the customer. Possible values are Off, Minimum, Medium and Maximum. Noise Figure. Gives the noise ratio for the selected transmitter. This value can vary from 0 good signal to average signal and to bad signal.

For some software versions, the noise figure will only be valid when Active Control is set to medium or maximum before activating CSM. Noise figure is not applicable for DVBT channels. Headphone Volume. Gives the last status of the headphone volume, as set by the customer.

The value can vary from 0 volume is minimum to volume is maximum. Attention: The presence of Dolby can only be tested by the software on the Dolby Signalling bit. If a Dolby transmission is received without a Dolby Signalling bit, this indicator will show OFF even though a Dolby transmission is received.

Surround Mode. Indicates the by the customer selected sound mode or automatically chosen mode. It can also have been selected automatically by signalling bits internal software. Audio System. Gives information about the audible audio system. This is the same info as you will see when pressing. When the audio is muted, there will be no info displayed.

Delta Volume. See DFU on how to change this item.. Preset Lock. Child lock. Lock after. Indicates at what time the channel lock is set: OFF or e. Parental rating lock. Gives the last status of the parental rating lock as set by the customer. Parental rating status. Gives the value of the parental rating status as sent by the current preset.

TV ratings lock. Only applicable for US. Movie ratings lock. V-Chip TV status. V-Chip movie status. Region rating status RRT. On timer. Gives the last status of the location setting as set via the installation menu. Possible values are Shop and Home.

If the location is set to Shop, several settings are fixed. So for a customer location must be set to Home. Can be changed via the installation menu see also DFU. HDMI key validity. IEEE key validity. Not applicable. POD key validity. Tuner Frequency. Indicates the frequency the selected transmitter is tuned to. TV System. Gives information about the video system of the selected transmitter.

Current main SW. Displays the built-in main software version. In case of field problems related to software, software can be upgraded. As this software is consumer upgradeable, it will also be published on the Internet. Flash utils SW. Displays the software version of the software which contains all necessary components of the download application. Standby SW. Displays the built-in stand-by processor software version. MOP SW. Not applicable for this chassis. Pacific 3 Flash SW. Displays the Pacific 3 software version.

NVM version. Displays the NVM version as programmed by factory. The Service Mode can be activated by disconnecting connectors 1M59 and 1M49 and then by shorting for a moment the two solder pads [1] on the Ambi Light Inverter Panel. See figure Service Mode pads AmbiLight panel. Indicates which source is used and the video quality of the selected source. Tuned Bit. Due to the DVBT architectural setup this item does not give useful information any more.

Digital signal modulation. No useful information for Service purposes. Displays the 12NC number of the onezip file as it is used for programming software in production. In this one-zip file all below software version can be found. Initial main SW. Displays the main software version which was initially loaded by the factory. In this chassis, both single and double fitted boards can be used. The double fitted boards are used in sets with 3 or 4 sided Ambi Light units whereas the single fitted boards are used in sets with 2 sided Ambi Light units.

A double fitted board can drive 2 lamp units 6 lamps and a single fitted board can drive 1 lamp unit 3 lamps. See figure Building blocks of Converter Board for details. Switches the Ambi Light board to protection if needed in case of protection only the lamps switch off, no set protection is triggered. There are two ways of protection: parallel arcing protection and serial arcing protection. Parallel arcing protection is performed by sensing the switching frequency.

Serial arcing protection is performed by detection of arc in ground wire of the lamp units. In this case, the protection pulse is transmitted via an opto-coupler. Protection can be disabled by short-circuiting diode or capacitor or by connecting pin 8 of the microprocessor to ground. In case the Ambi Light switches off after two seconds, serial arcing or parallel arcing protection is active. Serial arcing protection can be excluded by disconnecting the opto-coupler; check for bad solder joints on transformer or lamp units.

Parallel arcing protection can be disabled by grounding pin 8 of the microprocessor. Usually the switching frequency normally 63 kHz will then be too high. Possible causes are one MOSFET of the converter has no gate drive or is broken, or there is a short-circuit of the output of the transformer. For the sets of this chassis however, a Common Interface CI is not implemented.

Therefore, any reference to POD in this diagrams should be neglected. Due to architectural reasons it is possible that the TV will end up in an undefined state e. In this case diagnose has to be done via ComPair. There are two possible situation: one for protections detected by standby software and one for protections detected by main software. When the TV is in a protection state due to an error detected by standby software and thus blinking an error and SDM is activated via shortcutting the pins on the SSB, the TV starts up until it reaches the situation just before protection.

So, this is a kind of automatic stepwise start-up. In combination with the start-up diagrams below, you can see which supplies are present at a certain moment. Important to know here is, that if e. The protection state is hardware wise identical to the standby state but has other, limited wake up reasons. Standby Supply starts running. If the protection state was left by short circuiting the SDM pins, detection of a protection condition during startup will stall the startup.

Protection conditions in a playing set will be ignored. The protection mode will not be entered. Wake up reasons are off. The audio protection circuit shuts down the supply autonomously. This triggers a set restart and during that restart so at this check here , it will be observed that the audio protection line is high and the audio protection mode is entered. As a result, when an audio protection occurs, the set will restart and will enter a supply protection mode because of a missing power supply.

They are low in the standby mode if the standby mode lasted longer than 10s. Switching on the power supply in an LPL scanning backlight set, also switches on the backlight supply.

This 5 second delay does not delay the startup of the display as this time is absorbed in the startup time of the rest of the system. The availability of the supplies is checked through detect signals delivered by dedicated detect-IC's going to the st-by P. A low to high transition of the signals should occur within a certain time after toggling the standby line. If an observers is detected before the time-out elapses, of course, the process should continue in order to minimize start up time.

Startup shall not wait for this detection and continue startup. Start polling the detect-3V3 every 40ms. P3 can always be on, switching of lvds is done through PNX. If this happens, only a cold boot can solve this removal of power supplies. Since this is not feasible in the current SW architecture, instead Standby mode is entered. AVIP default power-up mode is Standby. Because of a bug in the Pacific IC, all video and display related Pacific parameters should be initialized before initializing the ambilight related Pacific parameters.

If not, initializing the video and display related Pacific parameters will overwrite the ambilight parameters. Initialize audio and video processing IC's and functions according needed use case. Switch off RGB blanking after valid, stable video, corresponding to the requested output is delivered by the Viper.

Add ms delay before resuming startup to avoid transients because of slow rising high tension voltages. Important remark: release reset audio and soundenable 10 sec after entering standby to save power. If needed to speed up this transition, this block could be omitted. This is depending on the outcome of the safety investigations.

Switch off 12V LCD supply within a time frame of min. Caution: It is compulsory to connect the TV to the PC as shown in the picture below with the ComPair interface in between , as the ComPair interface acts as a level shifter. ComPair interface excl. Starter kit ComPair32 software registration version : Starter kit SearchMan32 software: ComPair32 CD update : year , year onwards. SearchMan32 CD update : year , year , year ComPair firmware upgrade IC: Transformer non-UK : Transformer UK : ComPair interface cable: ComPair interface extension cable: Specifications ComPair consists of a Windows based fault finding program and an interface box between PC and the defective product.

For this chassis, the ComPair interface box and the TV communicate via a bi-directional service cable via the service connector s. ComPair is a further development on the European DST service remote control , which allows faster and more accurate diagnostics. ComPair has three big advantages: 1. ComPair helps you to quickly get an understanding on how to repair the chassis in a short time by guiding you systematically through the repair procedures.

ComPair allows very detailed diagnostics on I2C level and is therefore capable of accurately indicating problem areas. You do not have to know anything about I2C commands yourself because ComPair takes care of this. ComPair speeds up the repair time since it can automatically communicate with the chassis when the microprocessor is working and all repair information is directly available.

The ComPair fault finding program is able to determine the problem of the defective television. BIU Uncommon Files. BIV Uncommon Files. BIW Uncommon Files. BIX Game Files. BIY Uncommon Files. BJ0 Uncommon Files. BJ1 Uncommon Files. BJ2 Uncommon Files. BJ3 Uncommon Files. BJ4 Uncommon Files. BJ5 Uncommon Files. BJ6 Uncommon Files. BJ7 Uncommon Files. BJ8 Uncommon Files. BJ9 Uncommon Files. BJA Uncommon Files.

BJB Uncommon Files. BJC Uncommon Files. BJD Uncommon Files. BJE Uncommon Files. BJF Uncommon Files. BJG Uncommon Files. BJH Uncommon Files. BJI Uncommon Files. BJJ Uncommon Files. BJK Uncommon Files. BJL Uncommon Files. BJM Uncommon Files. BJN Uncommon Files. BJO Data Files. BJP Uncommon Files. The program, called "Markdown," is available on the Daring Fireball website.

However, if you intend to edit an MD file, you may want to open it in a Markdown editor. Markdown editors provide editing and review tools that will help you apply Markdown syntax correctly.

Some Markdown editors include:. Programming file that contains an instruction pattern for each instruction that the target machine supports; referenced by the GNU Compiler Collection GCC , commonly used for compiling programs on Unix systems.

File created by Sharkport, a hardware accessory for the PlayStation 2; contains a PS2 saved game created by the Sharkport device; used for copying saved games to the PC and sharing them with other players; can be converted to other saved game formats, such as.

NOTE: Sharkport also now uses the. PS2 extension for saved games. Data file saved by Moneydance, a personal finance software program similar to Intuit Quicken or Microsoft Money; stores bank accounts, transactions, budgets, stock portfolios, and other information. An MD file is a MuseData musical score. It contains plain text code that represents a piece of music, as well as metadata describing that work.

While MD files are no longer widely used, you can still open them and use them to create sheet music in MuseScore.